|
|
|
| Engine / Vessel Monitoring |
 > PRODUCTS > NMEA-2000 Maretron Products
> Engine / Vessel Monitoring |
|
| |
 Engine / Vessel Monitoring
|
J1939 to NMEA 2000® Gateway |
|
· Converts J1939 Data to NMEA 2000® Data for Display on Compatible Equipment
(Furuno, Garmin, Maretron, Raymarine)
· Attaches to Any J1939 Engine, Transmission, or Genset
- Caterpillar, Cummins, Detroit Diesel, John Deere, Kohler, Northern Lights, Onan, Perkins, Steyr,
Volvo Penta, Yanmar, etc.
· Converts Following Data
- AC Generator Current, Frequency, & Voltage, Tach, Hours, Coolant Pressure &Temp,
Oil Pressure & Temp, Fuel Rate, etc. |
|
|
| |
Engine Monitoring System (Yanmar) |
|
· Converts Analog Data to NMEA 2000® Digital Data
· Converts Following Data if Engine is Equipped with Sensors
- Tach, Hours, Water Temp, Oil & Boost Pressure, Volts, Trim
· Converts Engine Alarms if Engine is Equipped with Switches
- Fuel, Boost, Coolant Level & Temp, Oil Pressure, Exhaust Flow
· Plugs Directly into Engine Wiring Harnesses
· Used With or Without Analog Gauges
|
|
|
| |
Tank Level Adapter |
|
· Adapts Resistive Tank Senders to NMEA 2000® (Royce, WEMA, etc.)
· American (240-30 ohm) or European (10-180 ohm) Standard Compatible
· Can be Calibrated for Irregular Shaped Tanks
· Can be Used With or Without Analog Gauges
· 16 Point Calibration
· Supports All Tank Types
- Fuel, Fresh Water, Waste Water, Live Well, etc |
|
|
| |
Rudder Angle Adapter |
|
· Adapts Resistive Rudder Senders to NMEA 2000®
· American (240-30 ohm) or European (10-180 ohm) Standard Compatible
· Can Be Used With or Without Analog Gauges
· End Point Calibration for Different Rudder Stop Angles |
|
|
| |
Alternating Current Monitor |
|
· Monitors AC Sources and Outputs Data to NMEA 2000® Network
· Monitors Utilities (Shore Power), Generators, and Bus Power
· Provides Voltage, Current, Frequency, Real Power, Reactive Power, Apparent Power,
Power Factor, and Imported & Exported Energy
· Supports Single Phase and Three Phase Systems
· Sealed Waterproof Enclosure |
|
|
| |
Direct Current Monitor |
|
· Monitors DC Sources and Outputs Data to NMEA 2000® Network
· Measures Voltage & Current of any DC Source or Load
· Advanced Battery Monitoring Including Temperature, Load Current, Charging Current,
and Terminal Voltage
· Computes Battery State of Charge, and Time Remaining
· Hall-Effect Sensor Slips Over Wire – No Connection Breaks as with Shunts |
|
|
| |
Switch Indicator Module |
|
· Monitors Switch Closure Devices and Broadcasts Status Over NMEA 2000® Network
· Detects and Reports Opens, Shorts, etc.
· Works with Maretron Supplied Detectors
- Heat, smoke, bilge water, carbon monoxide*, LP Detector*
- Magnetic switches, glass break, door, hatch, portholes, etc.
* Available Q2 2009
|
|
|
| |
Run Indicator Module |
|
· Monitors Both AC & DC Circuits and Reports Running Status Over NMEA 2000® Network
- Manual or Auto Switched Loads
· Indicates Whether or Not Various Devices are Running
- Bilge pumps
- Winches
- Running Lights
- Transfer Pumps
- Exhaust/Intake Fans |
|
|
| |
Temperature Module |
|
· Monitors Up to 6 External Temperature Probes and Broadcast Data Over NMEA 2000®
Network
- Four Channels of Thermistor Probes (-4°F to 176°F) and Two Channels of Thermocouple Probes
(32°F to 1652°F)
· Probe Applications
- Cabin, Engine Room, Equipment, Air Duct, Tanks, Exhaust Gas Temperature (EGT), etc. |
|
|
| |
Tank Level Monitor |
|
· Ultrasonic Tank Sender with NMEA 2000® Interface
· 1/8” Depth Accuracy (-25°C to 55°C)
· TLM100 40” Depth Tanks
· Can be Calibrated for Irregular Shaped Tanks
· 16 Point Calibration
· Supports All Tank Types
- Fuel, Fresh Water, Waste Water, Live Well, etc
· Non-Displacement Hulls Require Focus Tubes |
|
|
| |
Tank Level Monitor |
|
· Ultrasonic Tank Sender with NMEA 2000® Interface
· 1/8” Depth Accuracy (-25°C to 55°C)
· TLM150 32” Depth Gasoline Tanks
· Can be Calibrated for Irregular Shaped Tanks
· 16 Point Calibration
· Supports Gasoline Tanks Only
· Non-Displacement Hulls Require Focus Tubes
|
|
|
| |
Tank Level Monitor |
|
�� Ultrasonic Tank Sender with NMEA 2000® Interface
· 1/8” Depth Accuracy (-25°C to 55°C)
· TLM200 104” Depth Tanks
· Can be Calibrated for Irregular Shaped Tanks
· 16 Point Calibration
· Supports All Tank Types
- Fuel, Fresh Water, Waste Water, Live Well, etc
�� Non-Displacement Hulls Require Focus Tubes
|
|
|
|
|
